To create a TCP/IP configuration with the Dos Utility,
1) Locate a copy of the Dos Utility
2) To install software.
1) Switch to a dos prompt.
2) Insert the utility disk in floppy drive
3) At C:\ prompt change the drive letter to the floppy drive.
For example if your main drive letter is C: and the floppy drive A:
from the C: prompt change to A:
3) The syntax for installing the software installation is

A: install C 0

A= drive A

C= drive C

Type of installation

0 =  Standalone

There are additional install variables which are not required for most installations, for information on any of the additional options please refer the User and Reference Guide.

On completion of the utility installation type C: this command will take you to the install directory for the 494 controller, the directory created during installation is.

C:\494UP

The utility directory has three batch file .

For the 494E at the prompt type 494eup

For the 494T at the prompt type 494tup

And for the 494A type 494aup

Please check your product model for correct batch file.

To identify the controller model, you will have to look at the physical hardware.

For the 494E controller the installed feature cards can be as follows.

40 48 45 or 40 41, the feature cards can be any combination of cards.

The Sync card of 40 = 494E (This is the card which identifies the controller type.)

The Sync card of 64 = 494T

And the Sync card of 72 = 494A

The feature cards are all the same for all three models.

41,44,48 These are twinax cards.
42 Ascii card
43 Token Ring lan Card  4/10 Mpbs
45 Ethernet 10 Mbps Lan Card

Note:
  Only the 494e supports Tcp/ip.

Getting Started.

From the dos prompt ,the directory is c:\494up

type ,494eup to start the program

Use the arrow keys to select an option,  Configuration then press Enter.

Network Link Establishment   Configuration <= select this option.   Bridge Filter Configuration   Concurrent Diagnostics  Source Route Bridging Status  System Reset  Software Download Utilities

PC2 494E - Configuration Use the arrow keys to move the cursor, then press Enter. _AS/400 Connection Network Information LAN Gateway Keyboard Translation Frame Relay Bridging Save Configuration    F9= Enhanced Mode

Because the configuration is a TCP/IP ,the controller has to be in Enhanced mode.
F9 will select Enhanced Mode , from Figure above

_TCP/IP  press  Enter
Next select
_Ethernet


Fill in the IP information as see below.

PC2E-C-1-5A 494E - Configuration - AS/400 Connection - TCP/IP Ethernet 494E IP Address . . . . . . . . . . . . . . . [192].[168].[1 ].[10 ] Global Parameters (Required) Ethernet Frame Format . . . . . . . . . . . . . . . Ethernet  Type II Network (Subnet) Mask . . . . . . . . . . . . . [255].[255].[255].[0 ] Default Gateway IP Address . . . . . . . . . . . [192].[168].[1 ].[1 ] AnyNet Keep Alive Duration . . . . . . . . . . . . . . . . . . . . [3 ] H1 AS/400 System 1 AS/400 IP Address . . . . . . . . . . . . . [172].[16 ].[5 ].[11 ] F6 = continue

The 494E ip address has to be configured on the same network as the remote router,the router ip address acts as the controller gateway.

Next select Network Information

PC2E-C 494E - Configuration Use the arrow keys to move the cursor, then press Enter. Controller slot. . . . . . . . . . . . . . . Slot 2 Controller type. . . . . . . . . . . . . . . 41 - Twinaxial Controller AS/400 Connection _Network Information Keyboard Translation

The default network name is the same value as the as/400 network , to find the network name on the AS/400 type at the  command line  DSPNETA locate the default network name, also take note of the Local location this will be required,for field H1 1 As/400 LU Name
Note: most networks network name defaults to APPN.

PC2-1 494E - Configuration - Network Information - TCP/IP Ethernet Default Local Network Name . . . . . . . . . . . . . . . . . [APPN ] 494E LU Name . . . . . . . . . . . . . . . . . . . . . . . . [C494E01 ] 494E CP Name . . . . . . . . . . . . . . . . . . . . . . . . [C494E01 ] Default Mode Name . . . . . . . . . . . . . . . . . . . . . [QRMTWSC ] Permanent Ethernet Address on card . . . . . . . . . . . . Source of 494E Ethernet Address . . . . . . . . _Address typed below  494E Address Format . . . . . . . . . . . _Ethernet Address Format 494E Ethernet Address . . . . . . . . . . . . . . . . . 0200[49400003] Logical Connection: Retry Counter . . . . . . . . . . . . . . . . . . . . . . . . .[10 ] Retry Interval . . . . . . . . . . . . . . . . . . . . . . . . . [6 ]

Concurrent Host Attachment . . . . . . . . . . . . . . . . . . . _NO Printer Inactivity Timeout . . . . . . . . . . . . . . . . . . . [000] Synchronize date and time with primary AS/400. . . . . . . . . . _NO H1 AS/400 System 1 AS/400 LU Name . . . . . . . . . . . . . . . . . . . . . . [S106551 ] AS/400 Network Name. . . . . . . . . . . . . . . . . . . . [APPN ] 494E Network Name . . . . . . . . . . . . . . . . . . . . [APPN ] Mode Name . . . . . . . . . . . . . . . . . . . . . . . . [QRMTWSC ] Controller Session Initiation . . . . . . . . . . . . . . . . _NO Controller Session Not Terminated . . . . . . . . . . . . . . _NO

F6 to return then F6 back to Slot Selection.
In the 3rd figure the configuration contained a twinax card type 41 in slot 4, if the hardware you are configuring doesn't have have a second card save the configuration and end.
if there is a Twinax card in slot 4, down arrow to card slot and press enter.
Configure  slot 4
As/400 connection assign an IP address to the twinax card plus the as/400. location  H1
Assign a new IP address and add the as/400 IP address
config the network information.
From the network information the command F9 will copy the configuration from the information in slot 2.
Now change the 494E LU/CP names, all other information remains the same.

494E LU Name . . . . . . . . . . . . . . . . . . . . . . . . [C494E02]

PC2E-B 494E - Configuration - Slot Selection

Use the arrow keys to select an option, then press Enter.

Save Configuration

PC2-5 494E - Configuration - Save Configuration

To save the configuration data press Enter.

 Save Configuration File
Configuration File Name:

[C:\494UP\494CONF.DAT ]

Usage of this Configuration File:

_Normal Configuration

Now the configuration has been saved on the computer.
Save a copy of the configuration file to diskette, this can be on a blank diskette or the controller setup diskette.
To do this change the drive letter and delete the directory, see below.
Configuration File Name:

[A:\494CONF.DAT

Usage of this Configuration File:

_Normal Configuration

The configuration is now ready for transfer to the controller
Please follow instructions on how to save a normal configuration to a 494.