Knowledgebase
Online Technical Support
Software Upgrades: Please check our latest Download section.
Search Tip: You can increase the accuracy of your searches by using as many keywords as possible. Remove any common words such as "a", "or", "the" as they will be used in the search. Do not use any operands such as +, or quotation marks to enclose phrases.
|
Our FAQ
# |
Title |
1 |
Configuring a default gateway How do I configure a default gateway in the DS Family, CS9000 or Jetstream servers? |
2 |
Terminal dial in access through the serial ports This configuration goes over setting up the CS9000 for dial in access via Terminal application to be able to access serial devices on ports configured for Reverse Telnet. |
3 |
Cannot use the Save or Reboot command line options When using the Windows Telnet client to configure the serial server products, with CLI commands that require a Y/N answer is bypassed and returns back to the command line. In some cases, communication to attached serial devices will appear that the device's prompts are being echoed/repeated or displays double prompts or jumps an additional line. |
4 |
Configuring a Port to Port connection How to configure two Jetstream's/CS9000's for a port to port serial connection over the LAN. |
5 |
Cannot telnet from the console Cannot telnet from the Admin port or within an established Telnet session on the Jetstream or CS9000. |
6 |
Netload TFTP errors Trouble shooting errors when transfering files using netload on the Jetstream and CS9000. |
7 |
Configuring a simple PPP dial in connection How to configure a device server for a simple PPP dial in connection. |
8 |
Jetstream/CS9000 stops communicating on the LAN Shortly after bootup the Jetstream or CS9000 server it stops responding on the LAN. The console displays a message: deleting route to interface eth0 |
9 |
Re-Setting to Factory Default Outlines the procedures to reset Jetstream, Lanstream, IOLAN+, IOPRINT+, 833 servers and P-series routers to the factory default settings. |
10 |
How To Put Or Restore A Configuration Files Describes the technique to retrieve or restore the config files for IOPRINT+ , JSxxxx ,CS9000 , Lanstream , IOLAN+ or any P-series Router. |
11 |
|
12 |
|
13 |
Accessing the admin port from a Unix Host How to configure a Unix host to administer a Jetstream, Lanstream, or CS9000 via the Admin port. |
14 |
Setting the Term Type on the line or Telnet What the Term Type definition is used for on the Jetstream and CS9000 servers. |
15 |
|
16 |
Upgrading firmware for a Jetstream/CS9000 How to upgrade firmware on a Jetstream 8500, 4000, Lanstream 2000, and CS9000. |
17 |
Route daemon cannot be disabled using the OEM mode. Route daemon cannot be disabled using the OEM mode on the CS9000 using firmware version 3.20. |
18 |
How to connect using SSH. Some examples of using SSH to connect. |
19 |
NFS configuration for Remote Port Buffering. Some examples of NFS configuration for Remote Port Buffering, used with the CS9000 and Iolan SDS. |
20 |
Setting OEM modes and Services Descibes how to add bit values to hex values when configuring OEM modes or Services on the Jetstream or CS9000. |
21 |
PPP direct connect How to setup a Windows PC to direct connect to the serial interface on the Perle 833RAS, CS9000, and Jetstream using a Dialup PPP connection. |
22 |
Using a Perle Serial server and m3i for IP management How to use a Perle serial server in conjunction with a model 3i to give TCP/IP LAN PC's connectivity to the AS/400. |
23 |
|
24 |
Cable or Converter Chart Cable conversion table for the console (CS9000) and serial servers (Jetstream 8500, 4000, and Lanstream 2000). |
25 |
|
26 |
How to initiate a hardware break within a telnet session How to send a break to a serially attached device within a telnet session to the CS9000 or the Iolan SDS serial port. |
27 |
|
28 |
Disconnect a session when terminal is turned off How to cause the Jetstream or CS9000 port to reset the telnet/login session when the serial dumb terminal is turned off. |
29 |
RADIUS return attributes RADIUS return attributes for the JS8500, JS4000, LS2000, CS9000, and Iolan SDS. |
